Blow Moulding Machine PET Blow Molding Machine
Plastic Blow Molding Machine, Blow Moulding Machine, PET Blow Molding Machine

    Plastic Blow Molding Machine


  • Model Number:
    DMK-L3

  • Description:
    A.Brief Introduction

    DMK-L series are the most stable two-step fully-automatic pet stretch-blow moulding machines(reheat). It has one to six cavities and the maximum capacity of the products is 2L. It can blow bottles in shapes: carbonated, mineral, pesticide, cosmetics, wide-mouth, hot filling, and other packing containers, which is made of plastic of crystalline type, such as PET and PP etc.
    1).High Automatization
    2).High Intelligence:The machine can be controlled through touch screen and running status is shown on it.
    3).High Quanlity:Steady infrared heating system blowing and highly precise blow-mould closing system ensure quality.
    4).High Speed:2000BPH(2-cavity), 3000BPH(3-cavity), 4000BPH(4-cavity), 6000BPH(6-cavity).

    5).No Contamination:Closed production zone, good self-lubrication system avoid contamination.
    6).Low Cost:Low consumption of electricity, air and water.
    7).High Transparency:Easy maintenance, absolute safely, visual inspection, low noise.

    B.Settings:
    a).PLC colour display: SIEMENS(GERMANY)
    b).Pneumatic parts:FESTO(GERMANY)
    c).Controller of preform transfer:Servo motor National(JAPAN)
    d).Other electric parts are all world-famous brand

    C.Machine Features:
    C.1. Stable performance with advanced PLC.
    C.2. Conveying preforms automatically with conveyor.
    C.3. Strong penetrability and good and swift distribution of the heat by letting the bottles rotate by itself and revolute in the rails simultaneously in the infrared preheater.
    C.4. High adjustability to enable the preheater to preheat preforms in shapes by adjusting the light tube and the length of the reflecting board in the preheating area, and eternal temperature in the preheater with an automatic thermostatic apparatus.
    C.5. High safeties with security automatic-locking apparatus in each mechanical action, which will make the procedures turn into a state of safety in case of a breakdown in certain procedure.
    C.6. No contamination and low noise with the air cylinder to drive the action instead of the oil pump.
    C.7. Satisfaction with different atmospheric pressure for blowing and mechanical action by dividing the blowing and action into three parts in the air pressure diagram of the machine.
    C.8. Strong clamping force with high pressure and double crank links to lock the mold.
    C.9. Two ways of operating: automatic and manual.
    C.10. Safe, reliable, and unique design of the position of valve to make the air pressure diagram of the machine easier to understand.
    C.11. Low cost, high efficiency, easy operation, easy maintenance, etc, with automatic technological process.
    C.12. Contamination is avoided for the bottle body.
    C.13. Ideal effect of the chilling with the chilling system.
    C.14. Easy installation and starting
    C.15. Low rejection rate: less than 0.2 percent.

    ITEM
    DMK-L2
    DMK-L3
    DMK-L4
    DMK-L6
    Theoretical output
    2000
    3000
    4000
    6000
    Max.container volume
    1.25L
    2L
    1.25L
    0.7L
    Max.neck diameter
    38MM
    38MM
    38MM
    38MM
    Max.container diameter
    80MM
    105MM
    80MM
    60MM
    Max.container height
    320MM
    335MM
    320MM
    265MM
    Number of cavity
    2
    3
    4
    6
    Number of lamp
    28
    100
    70
    60
    Max.heating power
    42KW
    100KW
    84KW
    90KW
    Installation power
    50KW
    110KW
    95KW
    100KW
    Actual power consumption
    35KW
    45KW
    40KW
    50KW
    Operatating low pressure
    0.7Mpa
    0.7Mpa
    0.7Mpa
    0.7Mpa
    Low pressure consuming
    1400L/min
    2000L/min
    2000L/min
    2000L/min
    Blowing pressure
    3.5Mpa
    3.5Mpa
    3.5Mpa
    3.5Mpa
    High pressure consuming
    3500L/min
    5500L/min
    5000L/min
    4500L/min
    Operating pressure
    0.3-0.5Mpa
    0.3-0.5Mpa
    0.3-0.5Mpa
    0.3-0.5Mpa
    Temperatuer
    10℃
    10℃
    10℃
    10℃
    Flow rater
    30 L/min
    40 L/min
    40 L/min
    50L/min
    Machine dimension
    2.7x1.8x2.2
    3.5x2x2.2
    4x2x2.2
    4.9x2.15x2.2
    Machine weight
    3500Kg
    4200Kg
    4800Kg
    5000Kg

     



    Learn more about products detailed description, pricing and service, Please send mail to us!




More Products
Blow Moulding Machines
Injection Molding Machines
Preform Molds
Cap Molds
Closure Molds

Contact Info
Tel: 0086-576-84039111
Fax: 0086-576-84052345
petblowmoldingmachine.com

Key Contact:
Ms. Mabel
Online Inquiry
Chinese English German Spanish French Italian Portuguese Japanese Korean Arabic Russian

Demark Blow Molding Machines & PET Preform Mould Co.,Ltd. PET Blow Molding Machines, Made in China.
Manufacturer/Factory. Wholesale injection/blow molding machine, automatic, pet blow moulding machine, machines, reheat stretch-blow, pet-stretch, blowing machine, pet bottle machine, plastic machine, pet preform molds, injection molding, preform injection system and more.